Home General Step-By-Step Guide For Electric Water Heater Installation

Step-By-Step Guide For Electric Water Heater Installation

40
0
Electric Water Heater Installation

Installing an electric water heater is not that difficult task. You would be able to perform this job on your own. But before you handle this particular job, you should consider that you will need to perform some basic electrical and plumbing work.

If you do not have any experience to perform this particular job, then it would be best if you take the help of professional services related to water heater repair San Diego.

Talking about the electric water heaters, they last for about 8 to 10 years. In most cases, you need to replace this particular equipment after 8 to 10 years.

So, if you observe any leakage in the water heater, then it does not mean that this has reached the end of its life.

Instead of replacing the water heater, you need to repair this particular equipment. Many times, it is possible to repair a leak. However, if you observe the leakage source is the tank itself, then the best option would be to focus on replacing the water heater.

In this particular section, you will get to know about the detailed guide regarding the electric water heater installation.

Just, you will need some basic tools for installing the electric water heater in your house. With the help of this approach, you would be able to save your money and electric bills.

electric water heater

Steps To Follow For Installing Electric Water Heater

All that you need is to follow the below-mentioned procedures to install an electric water heater in your house:

Required Items And Materials

Some of the important tools that you require for accomplishing the job include:

  •         Hose
  •         Pipe dope
  •         Wrench
  •         Screwdriver
  •         Pipe cutter
  •         Soldering iron
  •         Voltage detector
  •         Protective glove

Step 1: Power Off The Electricity

The first important step is to disconnect the electricity and remove the old electric heater. After that, you should focus on draining a tank. This can be achieved through switching off the valves and also attaching a hose.

Apart from that, you can make use of any particular tools like a pipe wrench, tubing cutter, or screwdriver for the removal of the remaining connecting parts. To know more, you can consider clicking here.

Step 2: Disconnecting The Electric Wire

You should focus on disconnecting the electrical cables from the upper portion of the electric heater. For this, you need to double-check that the circuit is turned off specifically at the breaker box.

The next step is to check the wires with a voltage detector before you start the work. To prevent possible confusion at a later stage, you need to insert labeling or mark.

Step 3: Disengaging Of The Supply Pipes

This step involves detaching the cold and hot water supply pipes by cutting them off. This becomes a very important step to perform in case the manufacturer used copper piping for plumbing your water heater.

For cutting, you can use a cutter or tubbing pipe. In this case, you can use a soldering iron for soldering copper pipes specifically to the cold water inlet.

Step 4: Reconnecting The Electrical Wires

This particular step involves removing the junction box cover for accessing the electrical wires. Another important thing is to connect the ground wire specifically to the green ground screw.

After that, you should focus on joining the cables by twisting them using wire connectors. Replacing the junction box cover is also very important.

Step 5: Installing The Supply Lines

After you attach the supply line, you should focus on attaching the supply line. Next, it is important to connect both the cold and hot water supply lines.

The subsequent step is to join the cold water inlet and the cold water pipe specifically for the water heater. So, you need to install new water piping by replacing the old one.

Step 6: Attaching The Pressure Discharge Pipe And Temperature

If the T&P relief valve is not pre-installed, you should focus on installing a new one. It is not recommended to use an old valve.

Talking about the T&P valve, it contributes to preventing damage by automatic opening whenever there is excess temperature or pressure.

Another important thing is to check the length which your electric water heater uses. The next step is to check the end portion of the pipe as well as the fitting and then, connect it to the joint.

Step 7: Switching On The Circuit Breaker

It is suggested to switch on the circuit breaker. You should perform this particular step after your water heater is filled with water.

But, if you are finding any sorts of difficulties in performing all these steps, then you can take the help of a professional service related to water heater repair San Diego you can try this.

Final Words

So, the above-discussed ones are considered to be some of the most important steps that you need to follow for the installation of the electric water heater.

Author Bio:-

Aimee is a marketing manager at EZ Plumbing & Restoration. She loves to write about plumbing services, Water Damage Repair, slab leak repair, Hydro Jetting and AC & Appliance Installation San Diego.